Kingston Hyper X 4GB DDR4 2133MHz

kingston_hyper_x_4gb_ddr4_2133

New

PHP 3,250.00

Brand Kingston
Series FURY
Model HX421C14FB/4
Memory Standard DDR4 2133 (PC4 17000)
Type 288-Pin DDR4 SDRAM
Interface 1.2V

HyperX FURY DDR4 Memory
Auto-overclocking for X99 platforms.

HyperX® FURY DDR4 can handle even the toughest battle. It recognizes its host platform and overclocks to the highest frequency published (up to 2666MHz*) — so you can wreak havoc. FURY DDR4 runs at 1.2V, even at 2666MHz, so it stays cooler while you play. You don't need to alter the voltage to reach higher speeds, which means there's more power for other hardware in the system. FURY's sleek, asymmetrical black heat spreader provides enhanced thermal dissipation to help keep your cool and help you stand out from the crowd.

  • Automatic overclocking — up to 2666MHz
  • Low power consumption at 1.2V
  • Optimized for X99 series motherboards
  • Stylish low profile heat spreader in black

HyperX FURY DDR4 Memory

Plug and Play
HyperX FURY DDR4 is the first product line to offer automatic overclocking up to the highest frequency published. Get the speed you want, without a hassle.

 
HyperX FURY DDR4 Memory

Optimized for Intel's X99 chipset
Complete your new X99 system with the latest generation of DRAM technology — DDR4 memory. HyperX FURY DDR4 memory is optimized for X99 motherboards for compatibility and easy overclocking.

 
HyperX FURY DDR4 Memory

Lowest power consumption
DDR4's lower power requirements mean less heat and higher reliability. Low 1.2V draws less power from your system for a cooler and quieter PC.

 
HyperX FURY DDR4 Memory

Low-profile stylish heat spreader
FURY's asymmetrical signature heat spreader is available in black with matching black PCB. It complements most X99 motherboards and its low-profile heat spreader fits under oversized CPU coolers while enhancing heat dissipation for lasting reliability.


*HyperX PnP memory will run in most DDR4 systems up to the speed allowed by the manufacturer's system BIOS. PnP cannot increase the system memory speed faster than is allowed by the manufacturer's BIOS.

Details

Capacity
4GB
Cas Latency
14
Timing
14-14-14
ECC
No
Buffered/Registered
Unbuffered
Color
Black
Heat Spreader
Yes
Features
HyperX HX421C14FB/4 is a 512M x 64-bit (4GB) DDR4-2133 CL14 SDRAM (Synchronous DRAM) 1Rx8, memory module, based on eight 512M x 8-bit FBGA components per module. Each module kit supports Intel Extreme Memory Profiles (Intel XMP) 2.0. Each module has been tested to run at DDR4-2133 at a low latency timing of 14-14-14 at 1.2V. Additional timing parameters are shown in the Plug-N-Play (PnP) Timing Parameters section below. The JEDEC standard electrical and mechanical specifications are as follows:

Note:
The PnP feature offers a range of speed and timing options to support the widest variety of processors and chipsets. Your maximum speed will be determined by your BIOS.

JEDEC/XMP TIMING PARAMETERS
JEDEC/PnP: DDR4-2133 CL14-14-14 @1.2V
XMP Profile #1: DDR4-2133 CL14-14-14 @1.2V

FEATURES

Power Supply: VDD = 1.2V Typical
VDDQ = 1.2V Typical
VPP - 2.5V Typical
VDDSPD = 2.2V to 3.6V
Nominal and dynamic on-die termination (ODT) for data, strobe, and mask signals
Low-power auto self refresh (LPASR)
Data bus inversion (DBI) for data bus
On-die VREFDQ generation and calibration
Single-rank
On-board I2 serial presence-detect (SPD) EEPROM
16 internal banks; 4 groups of 4 banks each
Fixed burst chop (BC) of 4 and burst length (BL) of 8 via the mode register set (MRS)
Selectable BC4 or BL8 on-the-fly (OTF)
Fly-by topology
Terminated control command and address bus
Height 1.23" (31.25mm), w/o heatsink
Fan Included
No

No customer comments for the moment.

Write a review

Write a review